September 30, 2024 / temp

BrosTrend 1 km Outdoor Wireless Bridge CPE Setup Guide

There a not so many networking devices BrosTrend provide to the users. But there is one more other than BrosTrendWiFi extender setup to make Network Bridge in your house. It is BrosTrend 1 km Outdoor Wireless Bridge CPE. Here, you will get to learn about BrosTrend 1 km Outdoor Wireless Bridge CPE Point-to-Point setup guide;

Setup Guide for BrosTrend CPE Bridge

There are two networking devices in the content package; you will get one PoE injector and one CPE device. Let’s see the hardware (ports and buttons of both devices).

BrosTrend CPE

You will get to DC jack, which you can use to supply power to the device.
LAN portis given on the back, which help you to connect other devices.
Reset button is given to the back of the device to make the device default again.
Power cord and Ethernet cable to power and connection, you must cut out the inlet to fit the cables.

BrosTrendPoEInjector

There are will be a DC port to supply power to the PoE device.
One PoE port and one LAN portare given on the back of the injector.

Now, let’s see how to connect and complete the BrosTrend 1 km Outdoor Wireless Bridge CPE Point-to-Point Setup;

Point to Point Connection

There are simple steps for hardware setup of brosTrend devices; let’s see how to connect PoE Injector first;

Place both the devices together near to your home router.
Connect the Ethernet cable to transfer data between PoE injector to router.
Connect the cable one end to the LAN port of the PoE device and router
Insert the power cord to the DC port and connect the adapter to power socket.

Point-to-Point-Connection

Now, have a look at how to connect the transmitter (CPE) to the injector;

Simply connect the Ethernet cable to the Injector PoE port.
Connect the other end to the CPE LAN portto connect and supply power.

The first connect for transmitter is completed; now you should learn about how to create other connection for the Receiver.

Connect the Ethernet cable to the WAN port of the router.
Connect other end of the cable to the LAN port of the PoE injector.
Now, connect the power to the Injector and by using another Ethernet cable connect the Receiver Station.
Insert the cable ends to the Station LAN port and Injector PoE port to supply power and data.

Station-LAN-port

Now, it is time to configure the CPEs to connect Receiver and Transmitter, take a close look;

Configure CPEs (Receiver + Transmitter)

To setup the Bridging between the two connected devices (Receiver and Transmitter), you have to connect computer to the internet by linking with your PoE Injector, then follow some steps;

First setup AP (transmitter)

Open an updated web browser on your computer.
Enter the IP address given on the label of the transmitter (192.168.2.1).
Then, press Enterto begin the search; you will reach to the setup page.
Here, you have to enter the default login username and password.

First-setup-AP

The username as well password is ‘admin’. After entering and clicking Login button you will access to the interface.

Now, select the AP Mode and click on the Next button.
After that, you can easily customize your WiFi username and key password.
Click Next to save all the settings and then carry onto the setting up receiver.

Second Setup Station (Receiver)

Open an updated web browser on your computer.
Enter the IP address given on the label of the Receiver (192.168.2.2).
Then, press Enter to begin the search; you will reach to the setup page.
Here, you have to enter the default login username and password.

Second Setup Station

The username as well password is ‘admin’
Now, select the Station Mode and click on the Next button.

Select the WiFi name of the AP (Transmitter) and enter the key password, click Next button.

Now, the setup is completed and you can use the devices to make network bridge in your house.